Heat Inverter Swimming Pool Heat Pumps
Heat Inverter heat pumps have the following features:-
- Unique "Inverter" technology improves overall efficiency and reduces running costs
- Inverter technology can improve efficiency by 15-20%
- High COP of 6.2 (at 26c)
- Advanced digital controller
- Operate at low temperatures - down to 0 degreees C
- Fully CE approved and manufactured to ISO standards
- Compressor capacitor specially designed and set at 130 degrees
- Automatic restart
- Intelligent defrosting design
- Low water flow protection
- Quiet operating levels
- Environmentally friendly
- Comprehensive guarantee
- Inverter technology
- Quiet operation
- Titanium heat exchanger with 5-year guarantee
- Digital Control Panel
- Quality built casing and components
With our new and improved Inverter technology, the heat pump very cleverly has the ability to continuously regulate its own thermal power flow (which can add 15% – 20% efficiency when compared to conventional technology.)
A traditional heat pump either works at maximum capability or is switched off as the compressor's speed cannot be varied. In order to regulate temperature a thermostat is used to measure the ambient air temperature and switch the compressor on when the water temperature is too far from the required temperature.
The Heatinverter uses a rectifier to convert the incoming AC current to DC and then uses pulse-width modulation of the DC current within an inverter (electrical) to produce AC current of a desired frequency. As the speed of a brushless motor is synchronised to the frequency of the AC current it is thus possible for the Heatinverter compressor to be run at different speeds. A microcontroller then samples the ambient air temperature and adjusts the speed of the compressor appropriately.
The effect of eliminating stop-start cycles is to increase efficiency, extend the life of components, and eliminate sharp fluctuations in the load the heat pump places on the power supply. This reduces the demand on the compressor which in turn reduces the running cost and improves efficiency.
The ‘Heatinverter’ range from HeatPumps4Pools operate down to an ambient air temperature of 0°C, with sizes from 12 - 30kw
Choosing to use a Heatinverter heat pump to heat your pool or spa will not compromise the temperature at which you are trying to maintain your pool or spa. Like any heater, as long as the correct size is selected, the required water temperature will be maintained throughout your swimming season.
Using a Heatinverter heat pump can be up to 6 times more energy efficient than other conventional types of heaters, which use either electricity, gas or oil for their fuel.
Models
The Heat Inverter models are available in single and 3-phase:-
Heat Inverter Models
| Model |
Electrical Power |
Heat Output
Kw |
Model FPPH30+ (12kw)
|
Single Phase 50hz, 230v |
12kw |
Model FPPH45+ (16kw)
|
Single Phase 50hz, 230v |
16kw |
Model FPPH60+ (23kw)
|
Single Phase 50hz, 230v |
23kw |
Model FPPH75+ (3 phase 30kw)
|
3-Phase 50hz, 380v |
30kw |
Specifications
(Note: the 23kw unit is single phase, there is an error in the above table showing it as 3-phase)
Pricing
Our prices are the total price payable and include delivery to UK addresses
Shipping
We can ship to any European country, please email us for a cost-effective shipping quote
Availability
All Heat Inverter products are normally in stock and will be delivered in approx 3-days from cleared payment.
We can deliver to anywhere in Europe. Please email your address for a shipping quote.
What size heat pump do I require for my pool?
Assuming your pool is covered when not in use, has low water table and you require a water temperature of approx 28c, please use the following tables which show the maximum pool size supported.
Aways oversize the heat pump where possible and do not select a unit operating at its maxiumum capacity:-
However many factors can affect the sizing of a heat pump for your pool. You are therefore strongly advised to contact us to get an accurate sizing recommendation for your particular pool.
Warranty
All Heat Inverter products come with the following warranty:-
- 2-years on-site parts and labour warranty in UK
- Parts only warranty on all components in the UK and Europe
- 5-year warranty on the titanium heat exchanger
- Warranty subject to the unit being installed in accordance with manufacturer's instructions.
Product Literature
Please click the links below to download pdf brochures for Heat Inverter products
Payment
We accept all major credit cards, cheques and Bank Transfer
NB: We offer a 1% discount for orders by debit card, bank transfer or cheque as we do not need to pay credit card processing fees.
Installation
Installation is straightforward. We can provide advice on installing your heat pump. We also offer a full installation service if required.
Please see our Installation pages for photographs of examples of pool heat pump installations and also the FAQ pages for more information
Assistance?
If you need any assistance or advice as to which model would be best for your pool, please email us
for more information, also see our FAQs page
All items sold in accordance with our terms and conditions
for all enquiries, please contact us at enquiries@heatpumps4pools.com
This product was added to our catalog on Saturday 12 June, 2010.
